 Разработка, производство и продажа радиоэлектронной аппаратуры  |
Требуется программист в Зеленограде
- обработка данных с датчиков; ColdFire; 40 тыс. e-mail:jobsmp@pochta.ru |
-----[Select and reset the controller]-----------------------
This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510dvr.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'sm510dvr.dll'.
The emulator adapter is titled 'SM510PCI POD Adapter'.
The emulator adapter is version '33.12.0.0'.
The emulator adapter is using 'Normal-Mode'.
The controller has a version number of '1' (0x0001).
The controller has an insertion length of '16' (0x0010).
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.
C:\CCStudio_v3.3\cc\bin>xdsprobe.exe -y
-----[Select the controller]-------------------------------------
This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510dvr.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'sm510dvr.dll'.
The emulator adapter is titled 'SM510PCI POD Adapter'.
The emulator adapter is version '33.12.0.0'.
The emulator adapter is using 'Normal-Mode'.
The controller has a version number of '1' (0x0001).
The controller has an insertion length of '16' (0x0010).
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).
-----[Test the emulator's JTAG controller hardware]--------------
Starting the Control Register Reset Test.
Finished the Control Register Reset Test.
Starting the Control Register Read-Write Test.
Finished the Control Register Read-Write Test.
Starting the Serial Buffer Normal Read-Write Test.
Finished the Serial Buffer Normal Read-Write Test.
Starting the Serial Buffer Reverse Read-Write Test.
Finished the Serial Buffer Reverse Read-Write Test.
Starting the Status0 Register Test.
Finished the Status0 Register Test.
Starting the Status1 Register Test.
Finished the Status1 Register Test.
Starting the Status2 Register Test.
Finished the Status2 Register Test.
Starting the Status3 Register Test.
Finished the Status3 Register Test.
Starting the Counter Capture Test.
Finished the Counter Capture Test.
Starting the Loop-Back with Reads and Writes Test.
Finished the Loop-Back with Reads and Writes Test.
Starting the Loop-Back Test with All-Ones Test.
Finished the Loop-Back Test with All-Ones Test.
Starting the Loop-Back Test Using All-Zeros Test.
Finished the Loop-Back Test Using All-Zeros Test.
Starting the Loop-Back with Recirculation Test.
Finished the Loop-Back with Recirculation Test.
Starting the Serial Buffer Observe Flag Test.
Finished the Serial Buffer Observe Flag Test.
Starting the State Command's State Machine Test.
Finished the State Command's State Machine Test.
Starting the Counter1 and Counter2 Test.
Finished the Counter1 and Counter2 Test.
None of the test-cases have detected errors.
C:\CCStudio_v3.3\cc\bin>xdsprobe.exe -i
-----[Select the controller]-------------------------------------------------
This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510dvr.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'sm510dvr.dll'.
The emulator adapter is titled 'SM510PCI POD Adapter'.
The emulator adapter is version '33.12.0.0'.
The emulator adapter is using 'Normal-Mode'.
The controller has a version number of '1' (0x0001).
The controller has an insertion length of '16' (0x0010).
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).
-----[Perform the scan-path length test on the JTAG IR and DR]---------------
This scan-path length test uses blocks of 512 32-bit words.
-----[The results of the scan-path length test on the JTAG IR and DR]--------
The test for the JTAG IR instruction scan-path length failed.
The JTAG IR instruction scan-path is stuck-at-ones.
The test for the JTAG DR bypass scan-path length failed.
The JTAG DR bypass scan-path is stuck-at-ones.
-----[Perform the scan-path integrity test on the JTAG IR]-------------------
This scan-path test uses blocks of 512 32-bit words.
Starting an Integrity Test using 0xFFFFFFFF.
-----[An error has occurred and this utility has aborted]--------------------
This error is generated by TI's USCIF driver.
The value is `-270' (0xfffffef2).
The title is: `SC_ERR_SCN_LENGTH_CONTROL'.
The explanation is:
The length of the scan is too large for the emulators controller.
Файлы
ccBrd0.dat
# config version=3.5
@ CPU_1 family=tms320c641x
$ sepk
pod_drvr=sm510dvr.dll
pod_access=direct
unify_clkmode=normal
$ /
# /
board.cfg
;cfg-2.0
[POD_DRVR] 'sm510dvr.dll'
[POD_ACCESS] 'direct'
[UNIFY_CLKMODE] 'normal'
ГДЕ ЧЕГО ПОКРУТИТЬ? спасибо.
