Телесистемы
 Разработка, производство и продажа радиоэлектронной аппаратуры
На главную   | Карта сайта | Пишите нам | В избранное
Требуется программист в Зеленограде
- обработка данных с датчиков; ColdFire; 40 тыс.
e-mail:jobsmp@pochta.ru

Телесистемы | Электроника | Конференция «Цифровые сигнальные процессоры (DSP) и их применение»

Ответ:

Отправлено stoker 25 декабря 2006 г. 15:08
В ответ на: Для начала (+) отправлено SM 25 декабря 2006 г. 14:59

и так, на команду xdsprobe -y выдало следующее:

-----[Select the controller]-------------------------------------------------

This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510usb.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'C:\CCStudio_v3.1\cc\bin\sm510usb.dll'.
The emulator adapter is titled 'SM510USB block-mode adapter'.
The emulator adapter is version '3.3.0'.
The emulator adapter is uses 'Block-Mode'.
The controller has an insertion length of '16' (0x0010).
The controller has a revision number of '1' (0x0001).
The controller type is 'The venerable TBC (74ACT8990)'.
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).

-----[Test the emulator's JTAG controller hardware]--------------------------

Starting the Control Register Reset Test.
Finished the Control Register Reset Test.

Starting the Control Register Read-Write Test.
Finished the Control Register Read-Write Test.

Starting the Serial Buffer Normal Read-Write Test.
Finished the Serial Buffer Normal Read-Write Test.

Starting the Serial Buffer Reverse Read-Write Test.
Finished the Serial Buffer Reverse Read-Write Test.

Starting the Status0 Register Test.
Finished the Status0 Register Test.

Starting the Status1 Register Test.
Finished the Status1 Register Test.

Starting the Status2 Register Test.
Finished the Status2 Register Test.

Starting the Status3 Register Test.
Finished the Status3 Register Test.

Starting the Counter Capture Test.
Finished the Counter Capture Test.

Starting the Loop-Back with Reads and Writes Test.
Finished the Loop-Back with Reads and Writes Test.

Starting the Loop-Back Test with All-Ones Test.
Finished the Loop-Back Test with All-Ones Test.

Starting the Loop-Back Test Using All-Zeros Test.
Finished the Loop-Back Test Using All-Zeros Test.

Starting the Loop-Back with Recirculation Test.
Finished the Loop-Back with Recirculation Test.

Starting the Serial Buffer Observe Flag Test.
Finished the Serial Buffer Observe Flag Test.

Starting the State Command's State Machine Test.
Finished the State Command's State Machine Test.

Starting the Counter1 and Counter2 Test.
Finished the Counter1 and Counter2 Test.

None of the test-cases have detected errors.

На команду xdsprobe -i :

-----[Select the controller]-------------------------------------------------

This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510usb.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'C:\CCStudio_v3.1\cc\bin\sm510usb.dll'.
The emulator adapter is titled 'SM510USB block-mode adapter'.
The emulator adapter is version '3.3.0'.
The emulator adapter is uses 'Block-Mode'.
The controller has an insertion length of '16' (0x0010).
The controller has a revision number of '1' (0x0001).
The controller type is 'The venerable TBC (74ACT8990)'.
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).

-----[Perform the scan-path length test on the JTAG IR and DR]---------------

This scan-path test uses blocks of 512 32-bit words.

The test for the JTAG IR instruction scan-path length succeeded.
The JTAG IR instruction scan-path length is 46 bits.

The test for the JTAG DR bypass scan-path length succeeded.
The JTAG DR bypass scan-path length is 1 bits.

-----[Perform the scan-path integrity test on the JTAG IR]-------------------

This scan-path test uses blocks of 512 32-bit words.

Starting an Integrity Test using 0xFFFFFFFF.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
Word 0: scanned out 0xFE03E0E2 and scanned in 0xFE2BE5E3.
Word 1: scanned out 0xFE03E0E2 and scanned in 0xFE2BE3E3.
Word 2: scanned out 0xFE03E0E2 and scanned in 0xFE2BE3E3.
Word 3: scanned out 0xFE03E0E2 and scanned in 0xFE6BE3E3.
Word 4: scanned out 0xFE03E0E2 and scanned in 0xFE6BE7E3.
Word 5: scanned out 0xFE03E0E2 and scanned in 0xFE6BE3E3.
Word 6: scanned out 0xFE03E0E2 and scanned in 0xFE2BE7E3.
Word 7: scanned out 0xFE03E0E2 and scanned in 0xFE2BE3E3.
The details of the first eight errors have been provided.
The utility will not report further errors found by this test.
Some of the 32-bit data values were corrupted - 99.8 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
Word 0: scanned out 0x01FC1F1D and scanned in 0x15FC7F7D.
Word 1: scanned out 0x01FC1F1D and scanned in 0x05FF7F7D.
Word 2: scanned out 0x01FC1F1D and scanned in 0x05FC7F7D.
Word 3: scanned out 0x01FC1F1D and scanned in 0x05FF7F7D.
Word 4: scanned out 0x01FC1F1D and scanned in 0x01FC7F7D.
Word 5: scanned out 0x01FC1F1D and scanned in 0x05FC7F7D.
Word 6: scanned out 0x01FC1F1D and scanned in 0x05FF7F7D.
Word 7: scanned out 0x01FC1F1D and scanned in 0x45FC7F7D.
The details of the first eight errors have been provided.
The utility will not report further errors found by this test.
Some of the 32-bit data values were corrupted - 99.8 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
Word 0: scanned out 0x5533CCAA and scanned in 0xFD77CFBA.
Word 1: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
Word 2: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
Word 3: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
Word 4: scanned out 0x5533CCAA and scanned in 0xFD77CFBA.
Word 5: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
Word 6: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
Word 7: scanned out 0x5533CCAA and scanned in 0xFD77CDBA.
The details of the first eight errors have been provided.
The utility will not report further errors found by this test.
Some of the 32-bit data values were corrupted - 99.8 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
Word 0: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 1: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 2: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 3: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 4: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 5: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 6: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
Word 7: scanned out 0xAACC3355 and scanned in 0xFECC33DD.
The details of the first eight errors have been provided.
The utility will not report further errors found by this test.
Some of the 32-bit data values were corrupted - 99.8 percent.
Finished that Integrity Test.
The JTAG IR integrity test has failed.

-----[Perform the scan-path integrity test on the JTAG DR]-------------------

This scan-path test uses blocks of 512 32-bit words.

Starting an Integrity Test using 0xFFFFFFFF.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
The JTAG DR integrity test has succeeded.


Составить ответ | Вернуться на конференцию

Ответы


Отправка ответа
Имя*: 
Пароль: 
E-mail: 
Тема*:

Сообщение:

Ссылка на URL: 
URL изображения: 

если вы незарегистрированный на форуме пользователь, то
для успешного добавления сообщения заполните поле, как указано ниже:
введите число 85:

Перейти к списку ответов | Конференция | Раздел "Электроника" | Главная страница | Карта сайта

Rambler's Top100 Рейтинг@Mail.ru
 
Web telesys.ru